E, ovako treba... > Aluminiumski čamci

Alu Angler

<< < (5/8) > >>

mossi:
EN AW 5083 [AlMg4,5Mn0,7]

Dakle legura ima 4.5%Mg(Magnezijuma) + 0.7%Mn (Mangana)  :good:

http://www.gleich.de/en/rolled-plates/en-aw-5083-details/?generatepdf

LSI:

--- Citat: Ufling  21, 09, 2010, 11:12:27 pre podne ---Hi All
Thanks for the translation, You are better than Google! And thanks for the positive comments!
Of course it’s ok to post the pictures; I decided to share them at picasaweb http://picasaweb.google.com/TeamUfling/AluAngler6605#  because I found it hard to find similar pictures of the building process when I considered building myself.  I think most manufactures are not willing to share detailed pictures because they are afraid that they will lose business..
As you have already seen the thickness of the material is on the first picture. Regarding the welding machine it’s a Kemppi Pro Evolution 4200 power sources and a ProMig 511 wire feeder with the MXE control unit http://www.kemppi.com/inet/kemppi/kit.nsf/DocsPlWeb/pro_evolution_all_langs_20091013.EN.pdf/$file/pro_evolution_all_langs_20091013.EN.pdf
I had no experience in MIG welding aluminum prior to beginning; it only took a few hours of training before I felt “god to go” the MXE are pre-programmed to weld in a lot of different alloys, so it’s just to chose the right material and thickness and the “finetune”
I used this wire, which gives the best strength result in 5083 plate http://www.alcotec.com/us/en/Almigweld/5183.cfm

Best regards
Uffe "Ufling" Nielsen
http://teamufling.blogspot.com

--- Kraj citata ---

Da pomognem malo:

"Pozdrav svima
Hvala na prevodima, Bolji ste od Google-a! I hvala na pozitivnim komentarima!
Naravno da je u redu da prikazujete slike; odlučio sam da ih podelim na picasaweb-u http://picasaweb.google.com/TeamUfling/AluAngler6605# zato što mi je bilo teško da pronadjem slične fotografije procesa izgradnje kada sam o tome počeo da razmišljam. Mislim da najveći broj graditelja nije voljan da podeli detaljne slike jer se plaše da će izgubiti posao..
Kao što ste već videli debljina materijala je na prvoj slici. Mašina za zavarivanje je Kemppi Pro Evolution 4200 power sources i ProMig 511 mašina za dodavanje žice sa MXE kontrolnom jedinicom http://www.kemppi.com/inet/kemppi/kit.nsf/DocsPlWeb/pro_evolution_all_langs_20091013.EN.pdf/$file/pro_evolution_all_langs_20091013.EN.pdf .
Nisam imao iskustva sa MIG zavarivanjem aluminijuma kada sam počeo; trebalo mi je par sati vežbe pre nego što sam osetio "može da se krene". MXE su pretprogramirani za zavarivanje velikog broja različitih legura, tako da je potrebno samo odabrati pravi materijal o debljinu i "fino podesiti".
Koristio sam ovu žicu, koja daje najbolju jačinu na 5083 tabli http://www.alcotec.com/us/en/Almigweld/5183.cfm

Najlepše želje
Uffe "Ufling" Nielsen"

Профа:
Uffe, can you tell us the price of your project ?
Without engine, just boat.

Профа:
You made design of a boat by yourself in CAD ? Useing these two books "Boatbuilding with aluminium" and "The elements of boat strength" like you said, without earlier knowlage you made  Alu Angler ?
You didnt used Rino or same other program to made design?

Профа:
With 115 HP Yamaha how fast you can drive, and how much fuel you need by hour?

Navigacija

[0] Indeks poruka

[#] Sledeća strana

[*] Prethodna strana